상점 페이지
Stormworks: Build and Rescue
전체 토론 스크린샷 아트워크 방송 동영상 창작마당 뉴스 가이드 평가

Stormworks: Build and Rescue

상점 페이지
Stormworks: Build and Rescue >  창작마당 > Uran_Wind 님의 창작마당
299 평점
ZE Modular Engine Controller
설명 토론0 댓글380 업데이트 노트
7
7
2
2
2
6
3
4
2
2
2
   
어워드
즐겨찾기
즐겨찾기됨
즐겨찾기 해제
Vehicles: Mechanical
Microcontrollers: Modular, Microcontroller
태그: v1.10.9
파일 크기
게시일
업데이트일
68.742 KB
2021년 3월 5일 오후 10시 46분
2024년 4월 11일 오전 6시 03분
업데이트 노트 28개 (보기)
제작자
Uran_Wind
오프라인
모음집 339개 모두 보기 (숨긴 상태 몇 개 있을 수 있습니다)
32,046 순 방문자 수
23,559 현재 구독자 수
377 현재 즐겨찾기 수

다운로드 위해 구독하기
ZE Modular Engine Controller

설명
Connect the blue composite node to any cylinder directly.
Do not insert extra logic gates between the composite cylinder node and the LUA script.
Disable the infinite fuel mode.
  • Maintains a constant engine RPS level set by a throttle value in range from 0 to 1, or by a desired RPS value set directly.
  • Compatible with turbocharged engines and automatically handles the increased air pressure made with impellers or electric pumps. The supercharger will be most effective if it can pump air pressure up to 60 atmospheres.
  • Mixture control mode can be switched between stoichiometry and air-to-fuel ratio. Property slider for the unselected mode will be ignored. In game terms, the stoichiometry value is the AFR with the engine temperature taken into account, and is preferable to adjust over a simple AFR. Toggle switch for optimal mixture shifts the stoichiometry to 0.5 at high load for maximum engine performance.
  • You can dynamically change the stoichiometry or air-to-fuel ratio with the corresponding node, if its value is in the same range as in properties.
  • Optional overheat protection activates at 105C and reduces RPS at higher temperatures. If your average fuel consumption per second per cylinder is lower than 0.005 liters, you don't need a cooling system as it takes a very long time for the engine to overheat, so you're more likely to run out of fuel sooner.
  • If you are not pumping air into the manifold and is fine with the default 13.8 AFR, you can remove nodes for the cylinder and dynamic mixture to shrink the controller's width and save some space.
Big thanks to Penatoliy for sharing the information about engine stoichiometry and exact formulas used in his ECU.
댓글 380개
< >
foxthedarkknight 2025년 1월 20일 오전 5시 44분 
it still works but you have to mess with the settings other wise the best engine micro controller around.
Stella 2025년 1월 18일 오전 10시 07분 
Yes.
Uran_Wind  [작성자] 2025년 1월 10일 오후 1시 32분 
No.
Gray 2025년 1월 10일 오후 1시 27분 
I think this is broken
Alfraido 2024년 12월 30일 오전 11시 26분 
I see, i was concerned for a moment, lol. But in the end it is simply a bit above my paygrade it appears
Uran_Wind  [작성자] 2024년 12월 30일 오전 5시 08분 
The are hooked inside the LUA script with functions property.getNumber()
Alfraido 2024년 12월 28일 오후 5시 44분 
Why are none of the settings you can change hooked into anything?
Uran_Wind  [작성자] 2024년 12월 28일 오전 11시 40분 
@Robert.4987 yes, at lower stoichiometry the engine consumes more air.
nuclear fission 2024년 12월 28일 오전 8시 46분 
can i use this on my creations if i link it?
Robert.4987 2024년 12월 26일 오전 8시 45분 
Hey youve probably heard this question alot but i couldnt find any question that fitted myself.
So i want to use Less fuel and more air but im stupid and dont really know how to fix it.

So if my stoichiometry is at 0.2 i believe it uses more air and less fuel instead of the 0.5

Is this correct or the opposite way?