상점 페이지
Cities: Skylines
전체 토론 스크린샷 아트워크 방송 동영상 창작마당 뉴스 가이드 평가

Cities: Skylines

상점 페이지
Cities: Skylines >  창작마당 > REV0 님의 창작마당
384 평점
Railway Erfurt-Nuremberg High Speed Rail (Wired)
설명 토론0 댓글47 업데이트 노트
   
어워드
즐겨찾기
즐겨찾기됨
즐겨찾기 해제
Assets: Transport, Transport Train, Road
파일 크기
게시일
43.777 MB
2019년 12월 31일 오후 5시 55분
업데이트 노트 1개 (보기)
필요한 아이템
이 항목에 필요한 다른 항목
제작자
REV0
오프라인
모음집 4332개 모두 보기 (숨긴 상태 몇 개 있을 수 있습니다)
43,963 순 방문자 수
28,322 현재 구독자 수
1,703 현재 즐겨찾기 수

다운로드 위해 구독하기
Railway Erfurt-Nuremberg High Speed Rail (Wired)

설명
Gruempental, Germany

The Nuremberg–Erfurt high-speed railway is a 190 km-long German high-speed railway, between Nuremberg and Erfurt. The line is listed in the Germany's federal transport plan as Verkehrsprojekt Deutsche Einheit Nr. ("German Unity transport project no") 8.1 and is a section of the high-speed route between Berlin and Munich and a section of the line connecting Italy and Scandinavia in the European Union's Trans-European Rail network.[2] It consists of an upgraded line between Nuremberg and Ebensfeld and a new line between Ebensfeld and Erfurt. The journey time between Erfurt and Nuremberg will be reduced to approximately one hour and 20 minutes after completion.

Part of Railway project


Network Content
  • Basic segment: Ground, ballastless with asphalt sub surface.
  • Elevated segment: Overpass from Erfurt.
  • Bridge segment: Grümpental Arch Bridge which is the second largest HST bridge of Europe.
  • Tunnel segment 1: Blessberg Tunnel
  • Tunnel segment2 : Blessberg Tunnel with extended ends, if combined with bridge on exit.

Network Features
  • Operational Speed: 300kmph
  • Noded tracks.
  • TEXTURE SHARE: Superstructure is based on RWY. If LSM is enabled, RAM use should be minimal.

Railway and Network Skins 2
You can use both or either of the mods to use the bridge. With Railway catenary selection is global, whereas catenary style can be customized per segment with Network Skins 2.

Acknowledgements
  • Part of Railway project

Recommended Mods
  • Road Anarchy: You know what it does.
  • Move It: In order to tweak or align the bridge properly.
  • Fine Road Anarchy: In order to switch different segment types such as elevated or bridge segment.

Keywords for Workshop search: Railway, REV0, Erfurt, High, Speed, Rail, HST, DB, Deutsche Bahn, Nuremberg, Nürnberg, Arch, Bridge, Ronyx, Netze, Grümpental, Gruempental
댓글 47개
< >
Vietkong69 2024년 6월 30일 오전 4시 16분 
Apparently it was and was pretty easy :D
Vietkong69 2024년 6월 23일 오전 11시 58분 
Any possiblities or how i could port this to use railway 2 wires or is it impossible?
Alecthelm 2023년 7월 21일 오후 3시 00분 
I love this Railway, use it simply everytime:)

@janne just use TM:PE mod, if you got it, if not...well get it:) or should the Maglev rush with 600 km/h into the STation;)
janne 2023년 5월 15일 오후 12시 51분 
Please increase the max. speed to min. 600 km/h to (Maglev)
REV0  [작성자] 2023년 2월 26일 오전 11시 17분 
It says LOD is too detailed that's it.

LSM Report doesn't factor the fact that this is a network, and networks must have at least 8 cuts for 64m mesh to curve them properly. It also doesnt take the fact that this is a massive arch span that is one of the largest bridges for CSL.

You can ignore that warning for the sake of this network.
ilcicci1983 2023년 2월 26일 오전 11시 10분 
Loading Screen Mod report said : Very large LOD mesh</a> 4761 vertices</i></div></div>.
It's a strange number it's an erro or intended?
REV0  [작성자] 2022년 12월 26일 오후 3시 25분 
1. bridges can not be curved, that's a game mechanic not network related. you CAN curve elevated segment however.
2. upgrade is yet another game limitation - upgrading bridges usually result with bridge being half upgraded or half arches. you can observe same behavior on vanilla roads, wehn you upgrade suspended bridges
skabeds 2022년 12월 26일 오전 10시 51분 
I'm having two issues.
1) You can only build the bridge in a straight line; even with Anarchy. The guide will show a curved line but the bridge will only go from A to B in a straight line.
2) The bridge arches only form full arches when building the bridge from scratch. If you try to upgrade an existing track it only creates half arches. Even when it is the same type of track. Ex: I tried to build an curved elevated track to be upgraded to a bridge track as a work around for the above issue. It did give me a curved bridge but all the arches were halved. I tested it on other bridges throughout my city with the same result; straight or curved. I also tried to build a curve with Network Multitool and got the same result.
REV0  [작성자] 2022년 10월 2일 오전 6시 19분 
it is not a station track, it's a bridge network.
Arisandi 2022년 10월 2일 오전 5시 53분 
how to replace the rail station with this track. no options listed